Beginner's Plumbing: The Essentials for Bathtub Installation
Beginner's Plumbing: The Essentials for Bathtub Installation
Blog Article
How do you feel with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old bathtub is conveniently available, the task can move easily; if you need to open a wall to get rid of the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to working with a specialist to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly help you install a brand-new tub in your restroom if you have actually currently bought a new tub and do not need to alter the plan of your previous supply of water pipes.
Your devices as well as material list should comprise the following:
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom should be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the remaining water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Making use of the two wood boards under its feet, position the bath tub in the called for setting. The wooden boards are practical in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by checking the spirit level as well as readjusting the feet on the bath tub up until the spirit level reads degree.
To set up faucets, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water and also check all joints and new pipework for leaks as well as tighten them if needed. Load the bathtub and also examine the overflow electrical outlet and the typical outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling and securing around the bath tub needs to wait till the bath tub has been used at the very least once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet and also the sink. Safeguard the tap in position with the producer supplied backnut. As soon as the tap is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The previous kind ought to be attached to the tap ends first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, creating the water to penetrate the wall in between the bath and the tiling, resulting in issues with dampness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components as well as installations. They are marketed in tubes and also cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly load the bathtub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can crack rather very early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

As an avid person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I was thinking sharing that excerpt was important. Sharing is good. One never knows, you may just be helping someone out. Thanks a lot for taking the time to read it.
Burst pipe? Phone! Report this page